Analog IC · Lesson 1

The MOSFET as an IC building block

g_m, r_o and intrinsic gain versus size and bias, with the small-signal model.

📘 Chapter introduction(click to show)

In this chapter you will learn to

  • ✓Tell the difference between the bias point (large signal) and small-signal behaviour.
  • ✓Calculate g_m, r_o and the intrinsic gain from I_D, W/L and λ.
  • ✓Explain how the overdrive voltage V_OV trades gain against transistor size.

1. Why this circuit matters

Almost every analog chip, from the audio circuit in your phone to a car's sensor interface, is built mostly from MOSFETs. On a chip, the transistor does nearly every job: amplifier, load, current source and switch. Before we can design any of those circuits, we need a simple way to predict how one transistor reacts to a small signal. That is what this chapter gives you.

💡 Think of it like this

Think of a MOSFET as a water tap. The gate voltage is how far you turn the handle, and the drain current is the water flow. g_m says how much extra flow you get for a small extra turn of the handle. r_o says how much the flow still changes when the pressure at the outlet (V_DS) changes. A perfect tap would ignore the outlet pressure completely; a real one does not, quite.

2. Definition

The small-signal model replaces a biased MOSFET with a voltage-controlled current source g_m·v_gs in parallel with an output resistance r_o between drain and source. It is valid for small changes around a fixed operating point.

3. Meet the components

NMOS transistor

Three terminals: drain (D), gate (G), source (S). The gate voltage controls the current from drain to source. The gate draws no DC current.

Bias current source

Sets the steady drain current I_D, and with it the operating point of the transistor.

Controlled source g_m·v_gs

In the model, this is the transistor's ability to turn a gate voltage change into a drain current change.

Output resistance r_o

Models channel-length modulation: the small rise in I_D as V_DS increases.

4. How it works, step by step

  1. 1

    Bias first. Choose V_GS so the transistor is in saturation and carries a steady current I_D. This is the operating point.

  2. 2

    Add a small signal. Put a small voltage v_gs on top of the bias. The square law is a smooth curve, so for a small change it behaves like a straight line: i_d = g_m·v_gs.

  3. 3

    g_m depends on the bias. g_m = 2·I_D / V_OV. More current, or a wider transistor at the same current, gives more g_m.

  4. 4

    The drain is not a perfect current source. I_D rises slightly with V_DS. We model that as a resistor r_o = 1/(λ·I_D) from drain to source.

  5. 5

    The best one transistor can do. If the drain drives only its own r_o, the voltage gain is g_m·r_o, the intrinsic gain. Every amplifier in this track is a way to get close to it, or beyond it.

🔑 The one thing to remember

Two numbers describe a transistor for small signals: g_m (how strongly it responds) and r_o (how well it holds its current). Their product is the most gain one transistor can give.

Device and bias

Key formulas

  • I_D = ½·k'n·(W/L)·V_OV²

    Square law in saturation, V_OV = V_GS − V_th

  • g_m = 2·I_D / V_OV = √(2·k'n·(W/L)·I_D)

  • r_o = 1 / (λ·I_D)

  • A_intrinsic = g_m·r_o = 2 / (λ·V_OV)

  • g_m / I_D = 2 / V_OV

    Transconductance efficiency

Large-signal bias and small-signal model

Biased transistorVDD100 µADSGMW/L=10saturationV_GS = 0.82 VSmall-signal modelGopen (no gate current)+ v_gs −DSg_m·v_gsr_og_m = 632 µS r_o = 200 kΩ
bias current I_D (→ direction of flow)controlled current source

Small-signal parameters

Overdrive V_OV316 mV
V_GS0.816 V
g_m632 µS
r_o200 kΩ
Intrinsic gain g_m·r_o126.5 V/V
g_m / I_D6.3 V⁻¹

Intrinsic gain vs drain current (this W/L)

1 µA10 µA100 µA1 mA1001 k126 V/Vg_m·r_oI_Dg_m·r_o (V/V)

Gain falls as current rises: g_m grows only as √I_D while r_o falls as 1/I_D.

Things to try

  • Double I_D and check that g_m rises by √2 ≈ 1.41, not 2.
  • Keep I_D fixed and increase W/L: V_OV falls, so g_m/I_D and the intrinsic gain both rise.
  • Double λ (a shorter channel) and watch r_o and the intrinsic gain halve.
  • Find the W/L that gives V_OV = 200 mV at 100 µA. That is a common design starting point.