Analog IC · Lesson 10
Noise
Thermal and flicker noise, corner frequency and integrated noise.
📘 Chapter introduction(click to show)
In this chapter you will learn to
- ✓Describe thermal and flicker (1/f) noise and where each comes from.
- ✓Refer a transistor's noise to its input and compare it with a signal.
- ✓Choose between more current and more gate area to lower noise in a given band.
1. Why this circuit matters
Every resistor and transistor produces tiny random fluctuations. They set the smallest signal a circuit can detect: a faint heartbeat in an ECG, a weak antenna signal in a radio, the last bit of an ADC. Noise inside the signal band cannot be filtered out, so it has to be designed down.
💡 Think of it like this
Think of the sound of a crowd in a stadium. Thermal noise is the steady murmur at every pitch. Flicker noise is a slow rumble that gets louder the lower the pitch you listen to. To hear one person speaking, their voice must rise above both.
2. Definition
Electronic noise is the random fluctuation of current and voltage in circuit elements. In a MOSFET it consists mainly of thermal noise (white, set by g_m) and flicker or 1/f noise (rising at low frequency, set by gate area).
3. Meet the components
Noiseless MOSFET
The ideal transistor in the noise model. All of its noise has been moved to the input.
Input noise source v_n
One equivalent voltage source in series with the gate. It represents all of the transistor's thermal and flicker noise.
Bias current
Sets g_m, and therefore the level of thermal noise.
4. How it works, step by step
- 1
Thermal noise. Carriers in the channel move randomly with heat energy. That produces a noise current proportional to 4kT·γ·g_m, the same at every frequency (white).
- 2
Flicker noise. Carriers are trapped and released at the gate-oxide interface. That produces slow fluctuations that grow at low frequency as 1/f.
- 3
Move it all to the input. We represent the total noise as one voltage source in series with the gate of a noiseless transistor. Now it can be compared directly with the input signal.
- 4
What each one depends on. Referred to the input, thermal noise is 4kTγ/g_m (more g_m, less noise) and flicker noise is K_f/(C_ox·W·L·f) (more gate area, less noise).
- 5
Corner and total. The corner frequency f_c is where the two are equal. What matters for a system is the total: the noise density integrated over the bandwidth you use.
🔑 The one thing to remember
Thermal noise falls with g_m (spend current); flicker noise falls with gate area (spend silicon). Your signal's frequency band tells you which to spend.
Device and bias
Integration band
Key formulas
v_n,thermal² = 4kT·γ / g_m
Input-referred, white. γ ≈ 2/3
v_n,flicker² = K_f / (C_ox·W·L·f)
Rises at low frequency
f_c = K_f·g_m / (C_ox·W·L·4kTγ)
Corner where they are equal
v_rms² = v_th²·(f₂ − f₁) + K_f/(C_ox·W·L)·ln(f₂/f₁)
Noise model: a noiseless transistor with an input noise source
Results
Input-referred noise spectral density
Things to try
- Quadruple I_D: g_m doubles, so the thermal floor falls by √2.
- Keep W/L fixed but scale both W and L by 4: thermal noise is unchanged, flicker drops by 4× in power (2× in voltage).
- Watch the corner frequency move as you trade thermal against flicker noise.
- Narrow the band to 10 Hz – 1 kHz (an audio or sensor band): flicker now dominates the total.
- Lower K_f (as for a PMOS input) and see the 1/f line fall.