Analog IC · Lesson 6

Five-transistor OTA

Live diff pair with mirror load: gain, GBW, slew rate and signal ranges.

📘 Chapter introduction(click to show)

In this chapter you will learn to

  • ✓Explain how the current-mirror load converts a differential signal to a single output.
  • ✓Calculate the OTA's gain, GBW and slew rate.
  • ✓Find the input common-mode range and output swing.

1. Why this circuit matters

Combine a differential pair, a tail current source and a current-mirror load, and you have the simplest complete amplifier used on chips: the five-transistor OTA. It turns a tiny input difference into an output current with high gain. You will find it in filters, comparators, voltage regulators, and as the first stage of most op-amps.

💡 Think of it like this

In a plain differential pair, each side reports half of the news on its own output wire. If you read only one wire, you lose half the story. The mirror load acts as a messenger: it carries the left side's half over to the right side, so one output hears both halves.

2. Definition

A five-transistor OTA (operational transconductance amplifier) is a differential pair (M1, M2) with a PMOS current-mirror load (M3, M4) and an NMOS tail source (M5). It gives a single-ended output current proportional to the input difference.

3. Meet the components

M1 and M2, input pair

Convert the input voltage difference into a current difference.

M3, diode-connected PMOS

Senses the left branch current I₁ and sets the shared mirror gate voltage.

M4, mirror output

Copies I₁ over to the right side, so the output collects both halves of the signal.

M5, tail current source

Sets the total bias current I_SS. In practice it is the output of another current mirror.

C_L, load capacitance

Whatever the OTA drives. It sets the bandwidth and the slew rate.

4. How it works, step by step

  1. 1

    The tail sets the budget. M5 fixes the total current I_SS, which splits between M1 and M2.

  2. 2

    M3 senses, M4 copies. M3 carries I₁ and, being diode-connected, sets a gate voltage. M4 shares that gate voltage and copies the current: I₄ = I₁.

  3. 3

    The output collects the difference. At the output node M4 pushes in I₁ and M2 pulls out I₂. The difference I₁ − I₂ flows into the load.

  4. 4

    Direction tells you the polarity. A positive input difference (V+ > V−) makes I₁ > I₂, so current flows into the output and V_OUT rises. V+ is the non-inverting input.

  5. 5

    High resistance gives high gain. The output node sees r_o2 ‖ r_o4, so the current produces a large voltage: A_v = g_m1·(r_o2 ‖ r_o4).

  6. 6

    The same current sets the speed. Driving C_L, the gain-bandwidth is GBW = g_m1/(2π·C_L) and the fastest possible slope is SR = I_SS/C_L.

🔑 The one thing to remember

The OTA is a transconductor: voltage difference in, current out. The mirror load lets a single output collect the whole signal.

Controls

Key formulas

  • I_out = I_4 − I_2 = I_1 − I_2

    The mirror delivers both halves of the signal

  • A_v = g_m1·(r_o2 ‖ r_o4)

  • GBW = g_m1 / (2π·C_L), f_p = 1 / (2π·R_out·C_L)

  • SR = I_SS / C_L

  • V_th + V_OV1 + V_OV5 ≤ V_CM ≤ V_DD − |V_GS3| + V_th

    Input common-mode range

Schematic (live)

PMOS current mirror: active load (M3 : M4)current-mirror tail biasVDDshared gate (mirror node)M3 diode-connectedVout2.58 VI_1−I_2 = 0 AV+V−SDGM3SDGM4DSGM1saturationDSGM2saturationI_TAILI_1 10 µAI_4 = I_1I_2 10 µA

Blue = left leg, green = right leg, amber = tail. Wire thickness follows the current. M4 copies I_1; the difference I_1 − I_2 goes to the output.

Performance

DC gain200 V/V (46.0 dB)
g_m1200 µS
R_out = r_o2 ‖ r_o41 MΩ
Dominant pole159 kHz
GBW31.8 MHz
Slew rate20.00 V/µs
V_OUT2.576 V
Output swing1.00 – 3.08 V
Input CM range0.80 – 3.08 V
V_OV input / load / tail100 / 224 / 200 mV

Transfer curve V_OUT vs V_id

-200.0-100.00.0100.0200.01 V1.5 V2 V2.5 V3 V2.58 VV_id (mV)V_OUT (V)

Small-signal gain around V_id = 0, clipped at the swing limits. This is a hand-analysis model, not a full nonlinear solve.

Open-loop frequency response

1 Hz100 Hz10 kHz1 MHz100 MHz10 GHz-2002040f_pGBW0 dBFrequency|A| (dB)

Things to try

  • Move V_id by ±1 mV and watch the output current arrow at Vout change direction.
  • Double C_L: GBW and slew rate both halve, but the DC gain stays the same.
  • Double I_SS: slew rate doubles, GBW rises by √2, and the DC gain falls (r_o drops).
  • Lower V_CM until it leaves the input common-mode range and see which limit you hit.
  • Increase the input W/L: g_m1 and GBW rise without spending more current.