Analog IC · Lesson 5

Differential pair

Watch the tail current steer between legs; gain, linear range and CMRR.

📘 Chapter introduction(click to show)

In this chapter you will learn to

  • ✓Explain how the tail current is steered between the two transistors.
  • ✓Calculate the differential gain and the linear input range.
  • ✓Explain common-mode rejection and what sets the CMRR.

1. Why this circuit matters

Real signals arrive with noise riding on them: supply ripple, interference, ground bounce. Very often that noise appears equally on both wires of a signal. A differential pair amplifies only the difference between its two inputs, so the shared noise cancels out. It is the input stage of almost every op-amp, comparator and ADC.

💡 Think of it like this

Imagine a seesaw with a fixed amount of sand shared between two buckets (the tail current). Tilting the seesaw (an input difference) moves sand from one bucket to the other, but the total never changes. Lifting the whole seesaw evenly (a common-mode change) moves no sand at all.

2. Definition

A differential pair is two matched transistors whose sources share a constant tail current. The difference between their gate voltages steers that current between the two branches and produces a differential output.

3. Meet the components

M1 and M2, matched input pair

Compare the two inputs and share the tail current between them. They must be identical for the circuit to be symmetric.

R_D, load resistors

Turn each branch current into an output voltage: V_out = V_DD − I·R_D.

I_SS, tail current source

Fixes the total current. On a chip it is a current mirror. Its output resistance R_SS sets how well common-mode signals are rejected.

Supply V_DD

Top of both load resistors.

4. How it works, step by step

  1. 1

    The tail sets the total. The tail source forces I₁ + I₂ = I_SS, always.

  2. 2

    Balanced inputs split it evenly. With equal inputs, symmetry gives I_SS/2 in each branch.

  3. 3

    A difference steers the current. Raise V_in1 slightly above V_in2: M1 conducts more and M2 conducts exactly that much less.

  4. 4

    Loads turn current into voltage. V_out1 falls and V_out2 rises. The output difference is A_d = g_m·R_D times the input difference.

  5. 5

    Common changes are rejected. If both inputs rise together, the tail still holds the total fixed, so the branch currents barely change.

  6. 6

    Large inputs switch it. Once |V_id| reaches √2·V_OV, one transistor carries all of I_SS and the other turns off. The pair then acts as a current switch.

🔑 The one thing to remember

A fixed total current that the inputs can only share: a difference moves it from side to side, a common change cannot move it.

Controls

Key formulas

  • I_1 + I_2 = I_SS

    The tail fixes the total; V_id only steers it

  • I_1 − I_2 = ½·k·V_id·√(4·I_SS/k − V_id²), k = k'n·W/L

  • g_m = √(k·I_SS), A_d = g_m·R_D (differential)

  • A_cm ≈ R_D / (1/g_m + 2·R_SS), CMRR = A_d,se / A_cm

Schematic

VDD 3.3 VR_DR_DV_out1 2.80VV_out2 2.80VDSGM1W/L=10saturationDSGM2W/L=10saturationV_in1V_in2I_1 100 µAI_2 100 µAI_SS 200 µAtail = current mirror
I_1 (left leg)I_2 (right leg)I_SS tail

Wire thickness is proportional to the current in each leg.

Results

I_1 / I_2100 µA / 100 µA
V_out1 − V_out20.000 V
V_OV (each, at V_id = 0)316 mV
g_m632 µS
A_d (differential)3.2 V/V
A_d (single-ended)1.6 V/V
R_SS (tail)100 kΩ
A_cm2.48e-2
CMRR36.1 dB
Linear range±447 mV

Current steering vs V_id

-50005000 A50 µA100 µA150 µA200 µA−√2·V_OV+√2·V_OVI_1I_2V_id (mV)Drain current

Things to try

  • Sweep V_id past √2·V_OV and watch one leg's wire thin to nothing: the pair has become a current switch.
  • Increase W/L: V_OV falls, the gain rises, but the linear input range shrinks.
  • Lower the tail λ (a stiffer tail, like a cascode mirror) and watch CMRR rise.
  • Raise R_D until a leg's drain falls below V_CM − V_th and the transistor enters triode.
  • Check that I_1 + I_2 always equals I_SS.