Analog IC · Lesson 3
Single-stage amplifiers
Common-source and source follower with a solved transfer curve and swing limits.
📘 Chapter introduction(click to show)
In this chapter you will learn to
- ✓Name the three single-transistor stages and say when to use each one.
- ✓Calculate the gain of a common-source stage with an active load.
- ✓Find the output swing limits from the saturation conditions.
1. Why this circuit matters
An amplifier makes a small signal bigger, or gives a weak signal the strength to drive a load. With one transistor there are exactly three ways to do it, depending on which terminal is shared between input and output. Every multi-stage amplifier, including the op-amp, is built from these three building blocks.
💡 Think of it like this
Think of a lever. Common-source is a long lever: a small push on one end gives a big, reversed movement at the other (high gain, inverting). The source follower is a stiff rod: the output follows the input almost exactly, but it can push a heavy load (a buffer). Common-gate is a lever pushed from the other side: gain without the reversal, but it takes a strong push to move it (low input resistance).
2. Definition
A single-stage amplifier uses one transistor, biased in saturation, to turn an input voltage change into an output voltage change. The terminal shared by input and output gives the stage its name: common-source, common-drain (source follower) or common-gate.
3. Meet the components
M1, amplifying NMOS
Turns the input voltage into a current change, with strength g_m.
M2, PMOS current-source load (common-source)
Carries the bias current and presents a high small-signal resistance at the output. It is the output side of a current mirror.
M2, NMOS current sink (source follower)
Pulls a constant bias current out of the follower's source.
Supply V_DD
Top rail. The output can swing only within the supply.
4. How it works, step by step
- 1
Common-source: input on the gate. A small rise in V_IN makes M1 conduct more current, by g_m·v_in.
- 2
The load resists the change. The PMOS load M2 tries to keep its current constant. The extra current from M1 has nowhere to go, so the output voltage falls until the two currents balance again.
- 3
High resistance means high gain. The output node sees r_o1 ‖ r_o2, which is large, so a tiny current change makes a big voltage change: A_v = −g_m·(r_o1 ‖ r_o2). The minus sign means the output moves the opposite way.
- 4
Source follower: output on the source. When the gate rises, the source rises with it so that V_GS, and the current, stay nearly constant. So V_OUT ≈ V_IN − V_GS, and the gain is just under 1.
- 5
Every transistor must stay saturated. That condition sets how far the output can swing. Push past it and the gain collapses.
🔑 The one thing to remember
Gain = how strongly the input changes the current (g_m) × how much resistance that current change works against at the output.
Controls
Key formulas
A_v = −g_m1·(r_o1 ‖ r_o2)
Inverting. The PMOS load is the output side of a current mirror.
V_IN − V_th ≤ V_OUT ≤ V_DD − |V_OV2|
Both transistors saturated
R_out = r_o1 ‖ r_o2
Common gate: A_v ≈ +g_m·(r_o1 ‖ r_o2), R_in ≈ 1/g_m
Theory only in this lab
Schematic
Operating point and gain
Transfer curve V_OUT vs V_IN
The steep part is the high-gain region, where both transistors are saturated. Its slope is the gain.
Things to try
- Press Bias at mid-rail, then compare the formula gain with the curve slope. They should agree closely.
- Raise V_IN by 10 mV in the CS stage and watch M1 drop into triode as the output falls.
- Halve λ and see the CS gain double, because both r_o values double.
- Switch to the source follower: the gain is about 0.9 and the output sits one V_GS below the input.
- Increase I_BIAS: g_m rises as √I but r_o falls as 1/I, so the CS gain drops.