Analog IC · Lesson 4

Cascode amplifier

Five load configurations compared: gain, output resistance and headroom.

📘 Chapter introduction(click to show)

In this chapter you will learn to

  • ✓Explain how a cascode transistor shields the input transistor.
  • ✓Estimate the cascode output resistance R_out ≈ g_m·r_o².
  • ✓Explain why a cascode needs a high-resistance load, and what it costs in headroom.

1. Why this circuit matters

The gain of a common-source stage is limited by r_o, and modern short-channel transistors have small r_o. To get more gain without spending more current, designers stack a second transistor on top of the first. This stack, the cascode, appears in almost every high-gain amplifier and precision current source.

💡 Think of it like this

Picture a worker (M1) who controls a flow of water, and a guard (M2) standing at the door. People outside push and pull on the door (the output voltage changes), but the guard holds it steady, so the worker's flow is not disturbed. The guard shields the worker.

2. Definition

A cascode is a common-source transistor (M1) topped by a common-gate transistor (M2) whose gate is held at a fixed voltage V_B. M2 shields M1's drain from the output and multiplies the output resistance by about g_m·r_o.

3. Meet the components

M1, input transistor

Common-source: converts V_IN into a current.

M2, cascode transistor

Common-gate with a fixed gate voltage V_B. Passes M1's current to the output and shields M1 from output changes.

Load current source

Supplies the bias current from V_DD. Its own output resistance limits the final gain.

Ground

M1's source connection.

4. How it works, step by step

  1. 1

    M1 does the converting. Exactly as in a common-source stage, M1 turns the input voltage into a current change.

  2. 2

    M2 passes the current up. M2 sits on top with its gate fixed at V_B and carries M1's current to the output.

  3. 3

    M2 holds node X still. If the output voltage rises, M2's gate is fixed, so its source (node X, M1's drain) rises only by ΔV_OUT / (g_m2·r_o2): almost nothing.

  4. 4

    So M1 barely notices the output. With node X nearly fixed, M1's current hardly changes. The output now looks like a much better current source: R_out ≈ g_m2·r_o2·r_o1.

  5. 5

    The load must match. Gain = −g_m1·(R_out ‖ R_load). A simple PMOS load (r_o) would dominate and waste the cascode, so high-gain designs cascode the load too.

  6. 6

    The price is headroom. Two stacked transistors each need about V_OV to stay saturated, so the output can swing less than in a plain CS stage.

🔑 The one thing to remember

The cascode buys about g_m·r_o times more output resistance and gain, and pays for it in voltage headroom.

Controls

Key formulas

  • R_out,cascode ≈ g_m2·r_o2·r_o1

    r_o1 multiplied by the intrinsic gain of M2

  • A_v = −g_m1·(R_out ‖ R_load)

  • Telescopic: A_v ≈ (g_m·r_o)² / 2

  • V_OUT,min ≈ 2·V_OV (cascode) vs V_OV (plain CS)

Small-signal values

NMOS g_m632 µS
NMOS r_o200 kΩ
PMOS r_o200 kΩ
Cascode R_out25.7 MΩ
NMOS V_OV316 mV
PMOS V_OV316 mV

Cascode stage

VDDideal loadV_OUTDSGM2W/L=10saturationV_B (fixed)X (barely moves)DSGM1W/L=10saturationV_INR_out ↓ ≈ g_m·r_o²
bias current (→ direction)output

Compare load configurations (click a row)

Selected: Cascode, ideal current-source load. The swing figure is V_DD minus the voltage the stacked transistors need to stay saturated.

Things to try

  • Compare 'Cascode, ideal load' with 'Cascode, simple PMOS load': the gain falls back to roughly the plain CS value.
  • Lower V_DD to 1.0 V and see which configurations run out of swing first.
  • Halve λ: the plain CS gain doubles, but the telescopic gain quadruples (it scales with r_o²).
  • Increase W/L to lower V_OV: you get more gain and more swing, at the cost of a larger device.